Filter By:
Seatposts
$62.00
The Velo Orange Grand Cru seatpost is made from one piece of aluminum, internally ovalized to trim weight. The Grand Cru seatpost’s head is integral with the post – not pressed on – for great strength and weight savings.
0mm Setback: Zero-setback/offset posts are commonly used on mountain bikes and by some bikepackers. The Grand Cru zero setback post uses a one-bolt, ergonomic side-adjustment mechanism for both saddle rail clamping and fore-aft adjustment.
30.2mm Setback: For riders who prefer the comfort of leather saddles but have found proper saddle placement difficult due the short rails on leather saddles Velo Orange offers the Grand Cru Long Setback with an ample 30.2mm of setback. This model uses a two-bolt design.
$861.00
Our intention with Reverb AXS was inventive and pure: No hoses. No routing. No energy wasted. Not a single thing in the way of the experience. We created a reliable wireless-electronic dropper post and controller that actuates with drastically less effort and zero distraction. Expanding what's possible on a bike, Reverb AXS is enabled by SRAM AXS technology, a new level of interaction, personalization, and connectivity across all AXS-enabled components.
- Effortless Electronic-Wireless actuation and infinite height adjustment with a single touch.
- Clean, simple and fast to install. No hoses to route, no fishing required.
- Updated internals for faster return speed in all conditions.
- New Vent Valve Technology, a simple and reliable built in service solution without disassembly of the seatpost.
- SRAM AXS technology, a new level of interaction, personalization, and connectivity across all AXS-enabled components.
- Includes RockShox AXS handlebar controller, rechargeable SRAM battery, and charger.
$100.00 - $149.99
- Highly tested & engineered unidirectional carbon tube offers outstanding fatigue & impact strength for a lightweight XC post
- Simple, lightweight 2 bolt design permits the saddle to be installed without disassembling the head
- Angled clamp bolts allow easy tool access for hassle free adjustment and tightening
- The rubber seatpost grommet fully seals the post to prevent water entering your seat tube
- Hunter head is suitable for most rail types 7/8mm alloy rails and 7/9mm carbon
- Wide lower cradle gives extra rail support for lightweight saddle rails
- Narrow upper cradle increases the amount of forward/back saddle adjustment
- Tilt Adjustment 6° up 12° down with Zero offset
$34.99
- RaceFace Ride XC Seatposts made of forged AL-6061
- Forged, anodized and shot peened AL-6061 mast
- 2-bolt head holds saddle securely while retaining easy adjustability
- Weight: 295 g
$199.50 - $229.50
The OneUp Dropper post is available in 120mm, 150mm, 180mm and 210mm lengths and all can be shimmed down in travel by 10 or 20mm.
We've been obsessed with shaving every last millimeter from the latest OneUp post to give you the the shortest stack height and shortest total length of any dropper post. No other post can get your saddle lower.
Starting from $199 USD with free shipping worldwide, cable actuated with reliable sealed cartridge internals for easy home servicing and includes travel adjust shims allow you to custom tune your post to dial in your perfect length.
The dropper market is dominated by expensive big brand posts and generic catalog shopped posts with different logos. We want to offer something better, a post with class leading specs, innovative useful features AND real value. Want more from your dropper? Get OneUp.
FEATURES
- Travel adjust shims allow you to custom tune your post to dial in your perfect length.
- Cable actuated for easy installation and a simple no bleed remote
- Ergonomic remote paddle position
- Reliable sealed cartridge internals
- User replaceable cartridge only $60 USD
- Easy to service at home
- 2 year warranty
UPDATES
- Shortest total length of any dropper
- Shortest stack height of any dropper
- New upper DU Bushing in the upper collar
- Increased bushing overlap and durability
- 100-210mm post lengths in 10mm increments.
- 20g lighter
SPECS
- Drop 120mm, 150mm, 180mm, 210mm adjustable*.
- Diameter 30.9, 31.6, 34.9
- Routing Internal only
Remote Compatibility:
- SRAM Matchmaker X - SRAM MMX clamps
- Shimano I-spec-EV - 12 speed XTR M9100, XT M8100 and SLX M7100
- Shimano I-spec II - 11 speed XTR M9000, XT M8000, SLX M8000 only
- 22.2mm Bar Clamp - All other groups 10 speed SHIMANO
- Cable clamping remote only (post requires cable stop to be assembled at base of post)
- Travel Reducing Shim Reduces travel by up to 20mm.
Weight Post Only
- (30.9) 120mm 435g / 150mm 480g / 180mm 525g / 210mm 570g
- (31.6) 120mm 450g / 150mm 500g / 180mm 545g / 210mm 590g
- (34.9) 120mm 545g / 150mm 605g / 180mm 660g / 210mm 710g
Remote Only
- Remote with 22.2mm Bar Clamp - 46g
- Remote with SRAM Matchmaker X / I-spec-EV - 43g
- Remote with Shimano I-spec-EV - 43g
- Remote with Shimano I-spec II - 41g
- Housing and Cable (1300mm installed length) - 50g
$28.00
Dimension Two-Bolt Seatposts provide a sturdy and durable saddle perch for cross country and all-mountain riding in three diameters, rigorously tested to ISO 4210 Mountain standards.
- Constructed with AL-6061-T6 aluminum
- Shot-peened finish
- 0mm offset
$320.00
Well, what´s to say about our new DIVINE SL? It is simply the lightest production dropper post in the world with a total length of 400mm and 80mm infinite drop.
Tailored to the needs of XC and marathon racers, the DIVINE SL is the youngest offspring of our dropper family. Based on the award-winning and patented REVIVE technology, we´ve modified the internals to work perfectly with the shorter travel. Of course, you can mount and use your DIVINE SL also on bikes outside the XC department. However, the DIVINE SL was specifically designed in respect of XC riders' requirements.
One of the features, is the "Tech-Climb" feature. While our DIVINE SL is completely locked in place in the top-out and bottom-out position for consistent riding position, the post can slightly spring in the middle positions. We´ve found out, that extremely steep and technical (e.g. rooty or rocky) uphill sections can be conquered with much more ease, when the saddle is just slightly dropped (lets say about 1-2cm). Having the saddle dropped just a bit (and not completely), the "Tech-Climb" feature" also adds some suspension to the post, flitering the impacts of roots and rocks. Back fully extended or fully dropped, the post is rigid again.
Titanium saddle bolts, carbon and oval rail compatible forged clamping plates, tapered tubes. All of this comes stock on the DIVINE SL to achieve a sensational low weight of 395g (30.9/400mm).
Another unique feature of our DIVINE SL:
- You can easily cut it to a short as 283mm, if you can spare the extra length with your frame and saddle height. The cut weight can go to a minimum of 345g!
- The shorter travel allows the DIVINE SL to come with a design, that doesn´t require manual resets like the REVIVE.
Of course, our DIVINE SL requires internal routing of the cable through your frame.
1 set DIVINE dropper post includes:
- 1x DIVINE SL Seatpost
- 1x cable housing 1500mm
- 1x Inner wire 1700mm
- 2x housing Endcap
- 1x remote (optional)
- 1x BikeYoke I-spec adapter or Splits-clamp (optional)
$320.00 - $410.00
3 years of REVIVE out in the market resulted in another benchmark product for BikeYoke: REVIVE 2.0. The new extralong 213mm REVIVE required a lot of re-thinking and re-engineering the whole chassis structure and since we think they deserve it, the shorter REVIVES will also get all the nice updates, and benefit from what was originally implemented only for the longest sibling of the REVIVE family.
Noteworthy updates of the REVIVE 2.0 include:
- One piece 3D-forged upper tube unit for improved stiffness and strength
- Fully hard-anodized pin seats in the upper tube for improved corrosion-resistance
- CNC-finished actuation lever for even smoother engagement
- New upper saddle clamp and saddle bolts with integrated conical washers for even simpler saddle installation
Wanna know more about the REVIVE? What if there was a dropper post, that actually solves and not just improves reliability issues, saves cost and time on the long run, and does not let you worry about too much time spent at service-centers? Or how about “bleeding” your seat post within a few seconds, while it is still installed in your bike?
BikeYoke presents the REVIVE dropper post, featuring one of the most brilliant design features in dropper post design in many years. More than 10 years of experience in drop-post design went into the “REVIVE” and the development has finally paid off.
Of, course, just as many other companies, BikeYoke would say, that REVIVE is reliable and strong and smooth. And yes, REVIVE is all of that, but not because we tried to improve current designs, but because we were thinking outside of the box and created a new concept, that is completely different from everything before.
To understand the benefits over other posts you have to know about the problems of many current designs first. Many of the popular current seatpost designs are based on a hydraulic lockout-system that relies on a perfectly sealing IFP (Internal Floating Piston), separating oil from air to prevent the seatpost from getting sagging or bouncing. There are a lot of difficulties to overcome when using an IFP because an IFP has to maintain 100% sealing function. If air could go to the oil side, your post will start becoming springy. This happens to a lot of posts in the market already and is the main issue why posts need to be serviced.
That´s why BikeYoke´s “REVIVE” features a NON-IFP design, because we think it is too difficult - if not impossible - to make a really reliable design using an IFP. REVIVE only requires 2 dynamic seals in the hydraulic circuit: The shaft sealing and the main piston sealing for the lockout mechanism. The highly critical IFP has been removed, and with it the need of perfect concentricity and finish of the sealing surfaces of the tubes. The lack of an IFP also results in the smoothest action you can think of.
The most important and ground-breaking feature of Revive is its “REVIVE-VALVE”. Even REVIVE can get air somewhere where it does not belong. This can happen for example when you actuate your seatpost while its upside down. And here is where the patented RESET VALVE comes into play:
- Insert a 4mm Hex Key into the REVIVE hex port, turn it and push down the post by hand.
- This will reset your hydraulic circuit on the fly - whenever. wherever. This is done just within a few seconds and only by the turn of a 4mm Allen key or the integreated mini reset lever, that comes with the post - of course without even having to remove your drop post from your bike.
So, now one might already understand that:
- No external air will want go inside the post´s hydraulic circuit, since it is charged with higher pressure, than its surroundings.
- No oil will go out (or at least very very little oil over the curse of a long time), because of very stable sealing - external sealing has never been a real problem of current post design
- The hydraulic system can be reset to “new” via the unique “REVIVE-valving”
- This means the hydraulic circuit is a very stable closed system and basically maintenance free.
Still there are parts that will need to be serviced sooner or later and when designing REVIVE it was put a lot of attention to maximum user-friendly serviceability:
- Bushings and keyway pins will wear over time. Usually, the pins wear first and you would want to replace them to reset your rotational play.
- Exchanging the pins and the lower bushing is simple and does not require any opening of the hydraulic system and can be done within less than 5 minutes.
1 set REVIVE dropper post includes:
- 1x REVIVE Seatpost
- 1x cable housing 1500mm
- 1x inner wire 1700mm
- 2x housing endcap
- 1x barrel cable clamp
- 1x air valve adapter
- 1x Quick-Reset-Lever
- 1x remote (optional)
- 1x BikeYoke I-spec adapter or Splits Clamp (optional)
- 1 set titanium saddle bolts and nuts (optional)
$350.00 - $390.00
Our award-winning REVIVE is also available as an oversized version for 34.9mm seattubes. Not only the lower tube diameter increased to 34.9, but also the stanchion tube grew form 25mm to 28mm. Finally there is a dropper that gives a stunning look in beefy seattubes while gaining strenght and stiffness at the same time. This is unrivaled by the competition. Optimized wall thickness and materials keep the weight extremely low and so our REVIVE MAX weighs in lower than some "regular" sized posts of the competition.
Let´s see, what´s special about our REVIVE posts:
What if there was a dropper post, that actually solves and not just improves reliability issues, saves cost and time on the long run, and does not let you worry about too much time spent at service-centers?
Or how about “bleeding” your seat post within a few seconds, while it is still installed in your bike?
BikeYoke presents the REVIVE dropper post, featuring one of the most brilliant design features in dropper post design in many years. More than 10 years of experience in drop-post design went into the “REVIVE” and the development has finally paid off.
Of, course, just as many other companies, BikeYoke would say, that REVIVE is reliable and strong and smooth, …
And yes, REVIVE is all of that, but not because we tried to improve current designs, but because we were thinking outside of the box and created a new concept, that is completely different from everything before.
To understand the benefits over other posts you have to know about the problems of many current designs first: Many of the popular current seatpost designs are based on a hydraulic lockout-system that relies on a perfectly sealing IFP (Internal Floating Piston), separating oil from air to prevent the seatpost from getting sagging or bouncing. There are a lot of difficulties to overcome when using an IFP because an IFP has to maintain 100% sealing function. If air could go to the oil side, your post will start becoming springy. This happens to a lot of posts in the market already and is the main issue why posts need to be serviced.
That´s why BikeYoke´s “REVIVE” features a NON-IFP design, because we think it is too difficult - if not impossible - to make a really reliable design using an IFP. REVIVE only requires 2 dynamic seals in the hydraulic circuit: The shaft sealing and the main piston sealing for the lockout mechanism. The highly critical IFP has been removed, and with it the need of perfect concentricity and finish of the sealing surfaces of the tubes. The lack of an IFP also results in the smoothest action you can think of.
The most important and ground-breaking feature of Revive is its “REVIVE-VALVE”.
Even REVIVE can get air somewhere where it does not belong. This can happen for example when you actuate your seatpost while its upside down.
And here is where the patented RESET VALVE comes into play:
- Insert a 4mm Hex Key into the REVIVE hex port, turn it and push down the post by hand.
- This will reset your hydraulic circuit on the fly - whenever. wherever. This is done just within a few seconds and only by the turn of a 4mm Allen key or the integreated mini reset lever, that comes with the post - of course without even having to remove your drop post from your bike.
So, now one might already understand that:
- No external air will want go inside the post´s hydraulic circuit, since it is charged with higher pressure, than its surroundings.
- No oil will go out (or at least very very little oil over the curse of a long time), because of very stable sealing - external sealing has never been a real problem of current post design
- The hydraulic system can be reset to “new” via the unique “REVIVE-valving”
- This means the hydraulic circuit is a very stable closed system and basically maintenance free.
Still there are parts that will need to be serviced sooner or later and when designing REVIVE it was put a lot of attention to maximum user-friendly serviceability:
- Bushings and keyway pins will wear over time. Usually, the pins wear first and you would want to replace them to reset your rotational play.
- Exchanging the pins and the lower bushing is simple and does not require any opening of the hydraulic system and can be done within less than 5 minutes.
1 set REVIVE dropper post includes:
- 1x REVIVE Seatpost
- 1x cable housing 1500mm
- 1x inner wire 1700mm
- 2x housing endcap
- 1x barrel cable clamp
- 1x air valve adapter
- 1x Quick-Reset-Lever
- 1x remote (optional)
- 1x BikeYoke I-spec adapter or Splits Clamp (optional)
- 1 set titanium saddle bolts and nuts (optional)
$60.00
RemiDemi EVO 1 Seatpost QR Conversion Assembly - Seatpost, QR Clamp and Shims
$285.00
- Designed using SRAM Exogram technology
- Available the Zipp SL Speed DI2 Internal Battery Mount to hold a Shimano DI2 seatpost battery within the SL Speed seatpost. (Sold separately)
- Matte Black finish
- Seat Post Diameter: 31.6mm
- Seat Post Length: 400mm
$285.00
- Designed using SRAM Exogram technology
- Available the Zipp SL Speed DI2 Internal Battery Mount to hold a Shimano DI2 seatpost battery within the SL Speed seatpost. (Sold separately)
- Matte Black finish
$172.00
The carbon Service Course SL seatpost is specifically tuned to be more shock absorbing than the "comfort" seatposts on the market, while still passing our strict internal MTB strength test. Flex engineered into the lightweight carbon tube keeps the rider comfortable over any terrain. Better fit means better performance, and if your saddle is out of position, you'll waste energy with every pedal stroke. The secure, two-bolt clamp makes for easy micro-adjustments of saddle position, and the head has been redesigned for maximum bolt-head accessibility. The Service Course SL seatpost makes it possible for nearly any rider to achieve the perfect fit, and the clamp works with all saddle rail types.
- Distinctive Zipp cosmetics
- Unidirectional Carbon fiber tuned for ride comfort
- Lightweight clamping system
- Lifetime warranty
$60.00
On today's road bikes, silver stands out amid the sea of stealthy black color schemes. This time-honored seatpost color is available on the Zipp Service Course Seatpost. Since the introduction of our line of Service Course and Service Course SL components, we've had amazing success with our pro-level athletes in all disciplines. While the successes have reinforced our design decisions, we have also drawn from their feedback. We not only learned how and why athletes make their equipment choices, but how our manufacturing methods and materials affect product performance. With new knowledge as well as new engineering, we are proud to offer redesigned Service Course seatposts.
- Material: 6061 aluminum
- 2-bolt adjustability
- Minimum insertion length: 90mm
$199.99
The X-Fusion Manic post uses internal cable routing and was designed around a low-profile seat cradle and seal collar to fit a broad range of frames. The mechanism is air-sprung and hydraulically locked. The remote can be run on the left or right, above or below the handlebar, but is optimized as a left shifter replacement for 1x drivetrains.
- Cable activated, hydraulic action, infinitely adjustable travel
- Double key-way design prevents lateral twisting
- Double bolt clamp with a wide range of seat angle adjustment. Fits both standard and 7 x 9 mm Carbon Rails
- Sealed cartridge internals for quick replacement
- Low profile head-seal and saddle clamp increase useable travel
$199.00
The X-Fusion Manic post uses internal cable routing and was designed around a low-profile seat cradle and seal collar to fit a broad range of frames. The mechanism is air-sprung and hydraulically locked. The remote can be run on the left or right, above or below the handlebar, but is optimized as a left shifter replacement for 1x drivetrains.
- Cable activated, hydraulic action, infinitely adjustable travel
- Double key-way design prevents lateral twisting
- Double bolt clamp with a wide range of seat angle adjustment. Fits both standard and 7 x 9 mm Carbon Rails
- Sealed cartridge internals for quick replacement
- Low profile head-seal and saddle clamp increase useable travel
$349.95 - $379.95
The Wolf Tooth Resolve Dropper Post is the first dropper post to use a self-bleeding cartridge. It has the shortest stack height of any dropper post on the market, has a short insertion depth, is one of the lightest dropper posts, and is completely serviceable at home.
- Self-Bleeding Resolve Cartridge: At the heart of Resolve Dropper Post is a self-bleeding cartridge that removes air from the fluid chamber with every actuation. All dropper posts can get air in the chamber, which leads to sag and squish. Resolve Dropper Post is the only dropper post that purges air from the chamber, which means you'll never need to buy a new cartridge as you do with all other dropper posts.
- Shortest Stack Height: The shortest stack height of any dropper post means that Resolve can get your saddle lower than any other dropper post. The lower your saddle, the more room you have to maneuver your bike on drops and techy descents.
- Weight and weight per travel is equal to the best: Resolve Dropper Post is one of the most lightweight dropper posts on the market when it comes to grams per millimeter of travel. It's as much as 26% lighter than other dropper posts of the same travel size.
- Short Insertion Length: When a dropper post has a short insertion length, longer travel options are unlocked for more bikes. A short insertion length is vital for smaller bikes, frames with curved seat tubes, and frames with seat tubes that have bottle bosses.
- Travel Reduction with Spacers: The travel length of your Resolve dropper post can be customized in order to suit your bike and saddle height. Spacer kits are sold separately or those who would like to have the adjustment made later by their local shop mechanic. If you are comfortable with working on suspension components, you may be able to complete the installation yourself.
$70.00
The Whisky No.7 Seatposts are made from the highest quality materials to be durable, lightweight, and comfortable. Whether you’re remounting during the cross race, or abusing them on the trail, you can trust Whisky’s seatposts. Available in different diameters and offsets.
- Convenient finger adjustment of saddle angle
- Unidirectional carbon shaft, forged aluminum head
- No rider weight limit
- 5 year Whisky warranty
- ASTM Condition 3 - For rough off-road riding and jumps less than 24"
$105.00
Seatposts can be an overlooked part of the bike, but at Whisky Parts Co., everything gets the same attention to detail so your ride never suffers. Their seatposts are made from the highest quality carbon, ensuring they are durable, lightweight, and comfortable. Whether you’re remounting during a cross race or abusing them on the trail, you'll be glad you have the No.7.
- Carbon shaft absorbs trail chatter
- UD carbon shaft, forged aluminum head
$54.99
WeThePeople's Socket Pivotal seat post is made from 6061 aluminum for a perfect blend of strength and weight savings. It works with all Pivotal seats and comes in the perfect color and size to match your bike. Plus, there's a 17mm socket head built into the bottom of the post for park-side adjustments to your wheels.
$39.99
WeThePeople's Team Pivotal seatpost is made from 6061 aluminum for a perfect blend of strength and weight savings. It works with all Pivotal seats and it's 200mm long for plenty of adjustability.
$479.95
Thomson Covert Elite Dropper Seatpost-31.6 150mm Black Internal.
We've set the bar with the Thomson covert black dropper post. It's designed around internal routing for clean installation and an updated shift style remote lever for effortless operation.
The Thomson Covert Dropper includes a new shifter oriented remote lever for easy operation. The cartridge-based system is designed to have the longest service life in the industry. If repair is needed, it's fast, affordable, and simple. Every part that makes up the Covert dropper is carefully chosen, and of the highest grade quality available.
- Custom made Norglide bearing bushings and Trelleborg O-Rings and seals
- Thomson saddle clamps and fasteners
- Motul Oil for durability and precision quality.
- The return speed is damped in the last 15mm of upward travel to be gentle on your seating area.
- 60mm (Ø27.2 only), 100mm, 125mm, 150mm of infinite travel.
- Passes ISO 4210 fatigue and strength tests for seat posts.
$29.99
The Tuner pivotal post features a 220mm length with grooves evenly spaced every 15mm for cut lines or seat height indication.
- 6061 alloy forged post
- Weight: 4.6oz
- Clamp Style: Pivotal
$29.90
- Strong and simple precision-forged aluminum seatpost
- One-bolt clamp design allows for a wide range of saddle angles with infinite intermediate adjustability
$35.90
- Retro-looking aero seatpost for road bikes
- Aluminum, body with a single bolt head
$50.00
The Salsa Guide Seatpost is designed to blend into the background; just like a good seatpost should. Strong, reliable, and always just where you left it.
- 6061 Aluminum shaft
- Two-bolt head
$104.00
The Salsa Guide Carbon Seatpost is lightweight, durable, and supportive when you need it most.
- Carbon shaft
- Bonded Aluminum two-bolt head
$70.00
The Salsa Guide Deluxe Seatpost is premium aluminum: lightweight, strong, and drama-free. Count on it to be there when you need it.
- 2014 Aluminum shaft
- Two-bolt head
$600.00 - $633.00
The new Reverb AXS XPLR dropper post delivers more control, confidence, and fun on gravel roads everywhere. Getting the saddle out of the way means more room to move, saving you from awkward maneuvering and sketchy descents. We created an all-new design complete with lightweight air-only internals featuring built-in compliance we call ActiveRide. It's like travel for your saddle. Enabled by SRAM AXS technology, Reverb AXS XPLR is part of the ultimate personalized cockpit.
- New 27.2mm Reverb AXS XPLR delivers more control, confidence, and fun for gravel
- ActiveRide—Air only internals provide a fully rigid top-out position. With the touch of your AXS controller, you've got built-in compliance to ensure comfort and control over the roughest sections of gravel
- Two travel options to choose—50mm or 75mm
- Saddle clamp options compatible with 7x10 oval carbon rails.
- Seat post length includes 400mm and 350mm (50mm drop only)
- AXS Technology allows rider customization via the AXS Mobile App
- AXS handlebar controls (drop or flat bar)
- Shared battery with all other SRAM AXS enabled components
- System is completely waterproof and dustproof to IP69K—take it anywhere
- SRAM AXS battery and charger included
SPECIFICATIONS:
- TRAVEL: 50mm, 75mm
- POST DIAMETER: 27.2mm
- POST LENGTH: 350mm, 400mm
- REMOTE: AXS Controller Sold Separately
- SADDLE RAIL COMPATIBILITY: Round/Oval (7x9 & 7x10), Round/Oval (7x9)
- WEIGHT (G): 562
- WEIGHT BASED ON: 75mm Travel 400mm Length W/O battery - Battery 25g
Page 1 of 4
Next page